How To Clean A 1911 45 Acp

Cleaning Instructions for a 1911 .45 ACP Pistol

1911 Cleaning Instructions

In this commodity, I am going to bear witness you, step by step, how to properly field strip and clean a 1911. I will use a Kimber Pro Carry Ii pistol for the sit-in. You will run into the gun cleaning tools and supplies that I have used with great results over the past 10 years of heavy gun use.

Here is some information on setting up a Homemade Gun Cleaning Station.

This Kimber .45 ACP model has a 4.25 "bull barrel" which has a different disassembly process than a 5" Government Model 1911. The main difference is the tool that is used to remove the slide.

Tools To Detach Your Kimber 1911

The Commander (Pro) models with 4.25″ bull barrel (bushingless) utilise a "take down" tool. This is the tool volition use to field strip the Kimber Pro Carry Ii in this article.

Kimber Take Down Tool — Kimber Take Downwardly Tool

If you have a five" barrel 1911, come across my videos: Field Stripping a Kimber 1911 Aegis Elite and Reassembly of a Kimber 1911 Aegis Elite. These videos will work for any 1911 that uses a barrel bushing, which is most 5″ Government models. You can view my step-by-stride instructions in the article: Field Stripping and Reassembling a Kimber 1911

The process is pretty easy and quick once yous take done it a couple times.

Dings in guide rod sleeve from Take Down tool

Update: I take noticed that repeated use of the Kimber Take-downwardly tool causes some marking on the stop of the guide rod. Hither is a picture of my Pro Carry.

My gun has seen better days, but if it was new, this would bother me. If you want to avoid this, there is a tool that slips over the end of the guide rod and does not harm anything. It volition be used at Step three below. It makes the 1911 field strip process much easier besides. I will be modifying the pictures soon to include this tool in the instructions. In the meantime, you lot can bank check it out here:

Kimber Ultra Tool

I recommend cleaning this gun later on every 200-300 rounds, or after every fourth dimension you shoot it.

Also, do non forget to replace your recoils spring regularly for best performance. Come across How and When to Supplant the Recoil Spring on your Kimber 1911.

I can tell you I have put thousands of rounds through this 1911 and accept had a few bug and replaced a few springs. I will explain all these things in another post. As well meet my post on a quick 1911 cleaning you lot tin can apply if yous can't take the gun apart.

Gun Cleaning Supplies

Here is what I use to clean a 1911:

Supplies needed to Clean a Kimber 1911 — Gun Cleaning Supplies

Boresnake or a rod and patches for a .45 caliber barre
Real Gorging Bore Dominate (New Improved Boresnake)
Menda Pump Chemic Dispenser
Kimber have-down tool (small L-shaped pin that came with your gun, or a small paper clip)
Optionally, 1911 Ultra Tool for Kimber Pro and Compact, will not damage your guide rod.
Hoppes Number 9 gun cleaning solvent
Slip 2000 EWL 30 or try the best, Veteran Owned Original Gun Oil. (Use Discount Lawmaking SAVEWITHDAVE)
Some gun cleaning swabs, cotton wool swabs and paper towels. Cream swabs work even better as they exercise non leave whatever strands backside.
Optional: Birchwood Casey Synthetic Safe Gun Scrubber

Salve Time Cleaning a 1911 by Using a Boresnake Instead of Rod and Patches

My favorite fourth dimension-saving tool is the Boresnake. I got one of these every bit a gift years ago and it is past far the quickest style to clean the butt of any gun. I now have iv of them. One for every quotient handgun and one for my AR-15 every bit well.

Before I started using the Boresnake, I used the standard rod and patch method, which works really well, simply takes a lot longer. This method involves soaking a small patch of material with solvent and forcing information technology through the butt with a rod. It comes out dirty, and you repeat this process with a new patch until information technology is make clean.

The Boresnake cleans the butt with 2 passes through the barrel and does an amazing task. They are pretty cheap and you tin make clean them in the washing automobile!

Kimber 1911 Cleaning Video

Y'all can picket the video below, or scroll down to the step-by-footstep Kimber 1911 gun cleaning instructions.

Field Stripping and Cleaning your 1911 Step-by-Stride with Pictures

Unload the gun

Unloading Kimber 1911 — Unloading the Kimber 1911

This is step number ane. Remove the mag, and empty the chamber in that order! Remove all ammo from the expanse.

Unload the gun again

This in case you skipped step number one. Please double bank check that the mag is out and the bedroom is empty. Encounter the 4 rules of Gun safe.

Remove the slide from the gun

Slide locked to rear Kimber 1911 — Lock the slide to the rear using slide finish lever.

Insert take-down pin Kimber 1911 — Insert the take-down tool into the hole in the guide rod.

Kimber 1911 slide released on take down pin — Gently release the slide lock lever allowing the slide to end against the take down tool.

Kimber 1911 line up slide lock lever — Slowly move the slide forrard until the slot in the slide lines up with the slide finish lever.

Kimber 1911 pulling out slide lock lever — Push button slide lock lever out from other side while pulling information technology toward y'all to remove.

Removing the slide from the Kimber 1911 — Pull slide off of the front end of the gun.

Removing the recoil assembly from Kimber 1911 — Elevator the guide rod assembly out of the slide.

Removing the barrel from the slide of a Kimber 1911 — Pull the barrel out the front of the slide.

Field Stripped Kimber 1911 — The gun is at present "Field Stripped" and ready for cleaning.

Clean barrel and guide rod assembly

Use Hoppes Number nine solvent & a rag or cotton swabs to clean the outside of the butt and guide rod assembly. Clean the inside of the barrel using a Boresnake that is the correct size for the quotient of the gun. In this example, 45 ACP.

Insert the pocket-size end of the Boresnake and pull it through slowly at charter 2 times. If the barrel is extremely dirty, y'all tin can utilise some Hoppes Number 9 to the snake to help things along.

Using Hoppes Boresnake to clean a Kimber 1911 barrel — To clean the within of the barrel, run a Boresnake through the barrel a couple times.

Wipe excess solvent off with a paper towel or soft cloth.

Clean the frame

Using Hoppes #9 solvent and a paper towel or cotton swabs, clean all surfaces of the frame, especially the rails where the slide contacts the frame. Alternatively, spray information technology downwards with Birchwood Casey Synthetic-safe Gun scrubber or equivalent. Later either method, employ a newspaper towel or rag to wipe all solvent off of the frame.

Lubricate

Using a quality lubricant such every bit Frog Lube, Slip 2000 (my preference as this is thicker than most and stays on the gun a long time) or Tri-catamenia superior Lubricant, apply sparingly to the following areas:

Frame:

Rail
Hammer pin
Slide finish
All moving parts in trigger control area

Slide:

Runway
Hammer cocking surface
Firing pin aperture

No demand for more than than a few drops. The oil volition movement around on its own and coat the necessary surfaces.

Reassemble the gun

This part is tricky the outset time you do it, but very easy one time you practise it a couple times.

Barrel and guide rod assembly in the slide of Kimber 1911 — Identify the barrel into the slide and permit it "lock" into place in the grooves. Then place the guide rod assembly on top equally shown.

Aligning slide with the frame of Kimber 1911 — Holding information technology all together, align the slide grooves with the frame and slide it on, making sure the barrels linkage loop is perpendicular to the butt.

Lining up the slide and barrel linkage to reassemble Kimber 1911 — Line up the slide lock holes on the slide with the barrel link.

Inserting the slide lock lever Kimber 1911 — Insert the slide lock pin through the slide.

Slide lock lever inserted into slide Kimber 1911 — Now line upwards the small-scale notch in the slide with the opening behind the detent pin as shown.

Push the slide lock lever past the detent pin into the slide. — Push button the slide lock lever past the detent pin into the slide.

Next, push button and lock the slide to the rear using the slide lock lever. Now the pressure level is off the take-down tool and it tin can be removed.

After removing the take-down tool, the gun is set to go. You volition want to work the slide a few times to aid spread the lubricant around every bit well as to make sure the gun is dorsum together properly.

Final Steps

If you want to exam the office of the gun, you can have some dummy rounds and load the gun and be sure it ejects a circular every time to rack the slide to the rear.

Perform a complete 1911 function and safe cheque.

There you lot accept it, step past footstep procedure on cleaning your Kimber 1911 pistol. Most of this process is the same for cleaning whatsoever 1911, just most practice non take the "balderdash butt" and the steps to removing the slide are slightly unlike.

As well run into my article on How to Clean a Springfield XD or XDm pistol.

See too my tutorial: How to Make clean a Babysitter .380.

If you have questions or comments, or a better product to use for cleaning or lubrication, please go out a comment below and I will respond!

Source: https://kydexowbholsters.com/how-to-clean-a-kimber-1911

Posted by: princeflaid1999.blogspot.com